Engels

Arabisch Catalaans Chinees Deens Duits Engels Frans Grieks Hebreeuws Hindi Hongaars Italiaans Japans Koreaans Nederlands Oekraïens Perzisch Pools Portugees Roemeens Russisch Slowaaks Spaans Thai Tsjechisch Turks Vietnamees Zweeds

Chinees

Definitie Arabisch Catalaans Chinees Deens Duits Engels Frans Grieks Hebreeuws Hindi Hongaars Italiaans Japans Koreaans Nederlands Oekraïens Perzisch Pools Portugees Roemeens Russisch Slowaaks Spaans Thai Tsjechisch Turks Vietnamees Zweeds

Favorieten

Publiciteit

interference fit

Definitie

firm joint assembled by force, causing slight mutual deformation ... See more

Vertaling van "interference fit" in Chinees

Definitie

NEW

过盈配合

盈配合

干涉配合

过盈量

It should choice proper interference fit between tungsten carbide rings and stainless steel seat ring.

其硬质合金环与不锈钢环座之间选用适当的过盈配合。

This innovative product replaces large fitted or interference fit bolts, no modifications required.

这一创新产品可取代较大的铰制孔螺栓或过盈配合螺栓，而不必进行任何改动。

Assembly technology of interference fit of sleeve and hole

套与孔的过盈配合装配工艺

Even with improved technological methods for fitting bolts, it is hard to achieve an interference fit.

即使采用改良的技术方式来装配螺栓，也很难取得过盈配合。

This paragraph is used to examine and check the parameters of a designed interference fit working at a specific operational temperature.

该段用来检验和检查工作在特别温度的干涉配合设计的参数。

Securing the transfer of the whole outer loading solely by friction between the connected parts is the basic requirement of interference fit loading capacity.

仅通过连接部分之间的摩擦固定转移整个外部负荷转移是干涉配合负载能力的基本要求。

Installation mode can be interference fit installation or gap gluing installation.

安装方式可以是过盈配合安装，也可以间隙打胶安装

With the main divided into three categories: clearance fit, transition fit, interference fit.

配合主要分为三类：间隙配合、过渡配合、过盈配合。

Hence the second stage 48 is where there is a higher force of torque trying to break the interference fit between screw 40 and screw shaft 50.

因此，第二级48是具有较大的破坏螺杆40和螺杆轴50之间的过盈配合的力矩的位置。

These tools allow drive-up forces to be applied effectively and evenly to the component with the interference fit avoiding raceway damage (fig 2) fig 1 fig 2

这些工具可使推进力有效、平稳地施加在这些过盈配合部件上，避免损坏滚道（图 2 ）图 1

Except for an end fitting that is attached by heat shrinking or by interference fit with plastic vacuum hose or that is attached by deformation of the fitting about a hose by crimping or swaging, at least one component of any end fitting shall be marked with the following information.

除通过热收缩或与塑料真空软管过盈配合进行固定的端接头，以及通过压接或型锻变形以配合软管的端接头外，端接头至少有一个部件标注有下列信息：

Thus, upon joining the lid 14 to the bowl 12, the first leg 34 is advanced over the annular nub 28 until the sealing point 5 engages the inner surface of the side wall to provide an interference fit between the lid and bowl.

因此，在把盖子14连接在碗12时，第一侧边34在环形节点28上方推进直到密封点5与侧壁的内部表面啮合以在盖子和碗之间形成过盈配合。