The car's software needed to revert back to its factory default settings.
車のソフトウェアは、工場出荷時の設定に戻す必要があった。
In addition, if you tap in the top right of the screen, will be reset to factory default settings.
画面右上の をタップすると工場出荷時の設定にリセットされます。
Note: passwords are cleared when the unit is reset to factory default settings.
注: ユニットが工場出荷時設定にリセットされると、パスワードは消去されます。
Removing the Password To clear the password access to the CCU, restore factory default settings.
パスワードの削除 CCUへのパスワードアクセスを消去するためには、工場出荷時設定に戻します。
Press and hold the reset button for 10 seconds to reset the device to factory default settings.
工場出荷時の設定にデバイスをリセットするには、リセット ボタンを 10 秒間押し続けます。
This restores factory default settings and restarts the V3.
を押す 工場出荷時の設定に戻し、V3 が再起動します。
In this case, we suggest you to connect the drive directly to IDE/SATA port on the motherboard/storage controller or to take the drive to a service center with the request to restore the drive to factory default settings.
この場合、ドライブをマザーボード/ストレージコントローラの IDE/SATA ポートに直接接続するか、ドライブをサービスセンターに持ち込んで工場出荷時の設定に復元するよう依頼することをお勧めします。
144 Restoring default setting values The factory default settings can be restored.
144 設定を初期値に戻す 工場出荷時の設定に戻すことができます。
Setting Reset Restore the recorder to its factory default settings.
初期化 工場出荷時の設定に戻します。
6 Factory Reset Reboots, restore factory default settings, or enter debug mode.
6 出荷時設定にリセット 再起動、工場出荷時設定の復元、またはデバッグモードに入ります。
Gamma is "HD NORMAL" and the other parameters are factory default settings.
標準の撮影に適したファイル F1: ガンマは HD NORMAL、 その他の要素は工場出荷時の設定になっています。
Tap Settings in the main menu Tap Service Tap OEM area Activate Remote access for screenshots with the ON/OFF slide switch Further information: "OEM area", Page 247 7.9 Backing up data 7.9.1 Back up settings The product's settings can be backed up as a file so that they are available after a reset to the factory default settings has been performed or for installation on multiple units.
メインメニューで 設定 をタップします サービス をタップします OEMエリア をタップします スクリーンショットのリモートアクセス を ON/OFF スライドスイッチで有効にします 詳細情報 : "OEMエリア" , 248 ページ 7.9 データのバックアップ 7.9.1 バックアップ設定 装置の設定をファイルにバックアップすることで、工場出荷時設定へのリセット 後、または複数の装置へのインストール用に使用できます。
Set Disconnect Message: TSP100IIILAN Online Manual When a network failure is detected (such as when a router and access point is disconnected or when an IP address cannot be acquired due to a DHCP server error), tsp100IIILAN will automatically print out a broken link (disconnection) warning message according to factory default settings.
リンク切れメッセージの設定 : TSP100IIILAN オンラインマニュアル TSP100IIILANは工場出荷時の設定により、ネットワーク機器(ハブなど)との接続が切断されたり、DHCPサーバーの不具合等によりIPアドレスが取得できないなどの ネットワーク障害を検出した際に、自動的にリンク切れ警告メッセージを印刷します。