Without a entry, resets all variables to their factory-default values.
エントリがない場合、すべての変数を工場出荷時のデフォルト値にリセットします。
If a var is specified, only the specified value only is reset to its factory-default value.
var が指定されている場合、指定の値のみが工場出荷時のデフォルト値にリセットされます。
NOTE: Values that have an asterisk ( ) are the factory-default values.
注記: アスタリスク ( ) が付いている値は、工場出荷時のデフォルト値です。
Factory-default reset: Like a hard reset, but removes any saved configurations and profiles.
工場出荷時のデフォルトリセット:ハードリセットと同様ですが、保存済みの設定やプロファイルも消去されます。
Could not restore the configuration to the factory-default settings
構成を出荷時のデフォルト設定に復元できませんでした
Settings to activate back-button AF The factory-default setting enables focusing by pressing the shutter button halfway.
親指AFを使うための設定 購入した状態では、シャッターボタンを半押しすることでピントが合うように設定されています。
Since all DS1859 devices have the same factory-default I2C slave address, it is therefore necessary to change the I2C slave address on one or more of these devices while they are still connected to the I2C bus.
どのDS1859デバイスも同じ出荷時デフォルトのI2Cスレーブアドレスを備えているため、これらのデバイスがI2Cバスに接続されている間に、1個以上のデバイスのI2Cスレーブアドレスを変更する必要があります。
When you go to press the shutter button all the way, the focus locks on the object in the center of the frame resulting in a failed photo More focusing freedom with back-button AF and AI Servo AF The factory-default setting on cameras enables focusing by pressing the shutter button halfway.
シャッターボタンを全押ししようとすると、中央にピントが合ってしまう(失敗) 親指AF+AIサーボAFモードで、ピント合わせの自由度がアップ! カメラを購入した状態では、シャッターボタンを半押しすることでピントを合わせる設定になっています。
RESTORE MODES Return all fuser-mode settings to the factory-default settings.
モードの復元 すべてのフューザモード設定を工場出荷時のデフォルト設定に戻します。
Zero Touch Provisioning (ZTP) is a mechanism by which network devices like switches can be configured from their factory-default state without any human intervention.
Zero Touch Provisioning (ZTP)は、スイッチなどのネットワークデバイスを人間の介入なしに出荷時のデフォルト状態を基に設定できるメカニズムである。
To restore the product to the factory-default settings, follow these steps.
プリン タを工場出荷時のデフォルト設定に戻すには、次の手順に従います。
When performing a hard reset or factory-default reset: The base station is set to request an IP address by DHCP.
ハードリセットまたは工場出荷時のデフォルトリセットを実行した場合は、以下のようになります。ベースステーションは、DHCP で割り振られる IP アドレスを要求するように設定されます。
Throughout the PPR process, FLARE 16 will continue to be the factory-default code revision for all CLARiiON Fibre Channel systems.
PPRプロセス全体を通じて、FLARE 16は引き続き、すべてのCLARiXファイバ・チャネル・システム用の工場出荷時のデフォルト・バージョンとなります。