Download for Windows Premium
Publiciteit
fault indicator

Vertaling van "fault indicator" in Japans

We konden deze vermelding niet vinden. Er worden benaderende resultaten weergegeven. Controleer je spelling of stel voor deze term aan het woordenboek toe te voegen.
障害 LED
障害インジケータ
故障表示器
故障指示器
The fault indicator light onthe replaced drives may be lit for a short time (one minute or less).
交換後のドライブの障害 LED が短時間 (1分以内) 点灯することがあります。
Replace all failed drives associated with this volume group (the fault indicator lights on the failed drives should be on).
このボリュームグループに関係するすべての不良ドライブを取り外します (不良ドライブの障害 LED が点灯しています)。
Verify that the power supply fault indicator light does not go on.
電源障害インジケータ・ライトがオンにならないことを確認してください。
If hardware, is there a fault indicator?
ハードウェアの問題である場合、障害インジケータは点灯しているか
Two open-drain fault indicator outputs notify the microprocessor when a short circuit, an open-load condition, or a short-to-battery condition exists.
短絡、オープン負荷状態、または天絡状態が存在する場合、2つのオープンドレインの障害インジケータ出力はマイクロプロセッサに通知します。
Wait until the new drive is ready (its fault indicator light must be off)before attempting to initialize the volumes in step 8.
新しいドライブが準備完了したら (障害 LED が消灯)、手順 8 のボリュームの初期化に進みます。
If power is not on, press the power button to begin powerup, and verify that the power supply fault indicator light does not go on ().
電源がオンになっていない場合は、電源ボタンを押して電源投入を開始し、電源障害インジケータ・ライトがオンにならないことを確認します()。
Because the drive has not failed, its fault indicator light will notbe turned on.
ドライブは機能しなくなっているわけではないため、障害 LED は点灯しません。
Wait until the replaced drives are ready (fault indicator light off)before going to step 6.
交換後のドライブが準備完了したら (障害 LED が消灯)、手順 6 に進みます。
The data on the affected volumes will be lost once you performstep 5. Be sure you have backed up your data before performing this step.. Remove the failed drive (its fault indicator light should be on).. Wait 30 seconds, then insert the new drive.
この手順を行うと、関係するボリュームのすべてのデータは失われます。手順 5 を行う前にデータのバックアップを取ったこととを確認してください。5. 不良ドライブを取り外します (障害 LED は点灯状態)。6. 30 秒ほど経過したら、新しいドライブを挿入します。
Wait until the new drive is ready (its fault indicator light must be off)before attempting to initialize the volumes in step 8.7. Wait for the initialization process is complete for the affected volumes.When initialization is completed, all volumes in the vdisk are Optimal.. Add the affected volumes back to the operating system.
新しいドライブが準備完了したら (障害 LED が消灯)、手順 8 のボリュームの初期化に進みます。7. 関係するボリュームに対する初期化が完了するのを待ちます。初期化が完了すると、仮想ディスクのすべてのボリュームが良好な状態になります。8. 関係するボリュームをオペレーティングシステムに追加し直します。
Active-low ALERT can be programmed to work in either fault indicator mode or interrupt mode.
アクティブローのALERTは、障害インジケータモードまたは割込みモードのいずれかで動作するように設定可能です。
If the fault indicator does go on, remove the power supply and then reseat it in the enclosure before referring to the Troubleshooting section of the AX100 support website or the documentation CD.
(障害インジケータがオンになる場合は、AX100サポートWebサイトまたはドキュメントCDのトラブルシューティングセクションを参照する前に、パワー・サプライを取り外し、エンクロージャに取り付け直してください。
Er zijn geen resultaten gevonden voor deze term.
Ga naar Premium voor toegang tot miljoenen vertaalvoorbeelden, onbeperkt woorden opslaan en leren, zonder advertenties.

Synoniemen voor fault indicator in het Engels

Woord & uitdrukking van de dag
Afbeelding van de dag
wings: feathered limbs used for flying
Ontdek het woord
Publiciteit

Suggesties

Resultaten: 25. Exact: 25. Verstreken tijd: 15 ms.