Vertaling van "kernel at" in Japans
We konden deze vermelding niet vinden. Er worden benaderende resultaten weergegeven. Controleer je spelling of stel voor deze term aan het woordenboek toe te voegen.
Most boot loaders will simply load the kernel at its target address directly.
ほとんどのブートローダは、単にそのターゲットアドレスにカーネルを直接 ロードするでしょう。
For example each file system built into the kernel registers itself with the kernel at boot time or, if you are using modules, when the file system is first used.
たとえば、あるファイルシステムがカーネルに組み込まれている場合、その個々のファイルシステムは起動時にカーネルに登録される。 あるいは、もしモジュールになっている場合は、ファイルシステムが最初に呼びだされたときに、登録がなされる。
To use different parallel ports for the printer and the PLIP cable, you can say Y to this printer driver, specify the base address of the parallel port(s) to use for the printer(s) with the "lp" kernel command line option. (See the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.
2)プリンタと PLIP ケーブルが違うパラレルポートに接続される場合,ここでは Y と答えてプリンタドライバをカーネルに組みこみ,プリンタが接続されているパラレルポートのベースアドレスをカーネルのコマンドラインオプションの "lp" を使って指定します(起動時にカーネルに与えるオプションの指定法についてはお使いのブートローダー(lilo か loadlin)のドキュメントを読んで下さい.
To use different parallel ports for the printer and the PLIP cable, you can say Y to the printer driver, specify the base address of the parallel port(s) to use for the printer(s) with the "lp" kernel command line option. (See the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.
2)プリンタと PLIP ケーブルが異なるパラレルポートを使う場合,プリンタドライバを組みこむことにしてカーネルのコマンドラインオプション "lp" でプリンタの使うベースアドレス(複数可)を指定してやります(起動時にカーネルにオプションを与える方法の詳細についてはお使いのブートローダ(lilo か loadlin)のマニュアルを読んでください.
As with file systems, the binary formats supported by Linux are either built into the kernel at kernel build time or available to be loaded as modules.
ファイルシステムの場合と同様に、Linux でサポートされているバイナリフォーマットは、カーネルをビルドする際にカーネルに組み込まれるか、ローダブルモジュールとして利用可能かのいずれかである。
Note that this driver will only probe for the Trantor T130B in its default configuration; you might have to pass a command line option to the kernel at boot time if it doesn't detect your card.
注意:このドライバは、デフォルト設定では Trantor T130B のみを検出しようとします。 もしカードを認識しない場合は、ブート時にカーネルにコマンドライン・オプションを渡さなければならないかもしれません。
You might as well try it out. Note that this driver will only probe for the Trantor T130B in its default configuration; you might have to pass a command line option to the kernel at boot time if it doesn't detect your card.
試してみるのも良いかもしれません. このドライバは,デフォルト設定では, Trantor T130B しか検出しませんので,もし使っているカードを見つけられない場合,起動時にカーネルにコマンドラインオプションを与えなければならないかもしれません.
First, Linux finds out which of the SCSI host adapters, or controllers, that were built into the kernel at kernel build time have hardware to control.
まず Linux は、カーネル構築時にカーネルに組み込まれた SCSI ホストアダプタもしくはコントローラのうち、制御すべきハードウェアを持つのはどれなのかを見つけだす。
Falco uses system calls to secure and monitor a system, by: Parsing the Linux system calls from the kernel at runtime Asserting the stream against a powerful rules engine Alerting when a rule is violated For more information, see Falco Rules. What does Falco check for?
Falcoは実行時にカーネルからのLinuxシステムコールを解析し、強力なルールエンジンに対してストリームをアサートします。 ルールに違反した場合は、Falcoのアラートが発せられます。 Falco rules についてもっと読む Parse Assert Alert Falcoは何を見ているのか? デフォルトでは、Falco には成熟したルールのセットが同梱されています。
The main thing is that you have a good semantic kernel at your exit without garbage requests.
主なことは、ゴミ依頼なしであなたの出口に良い意味カーネルを持っているということです。
You normally call the kernel at this address to start it booting.
カーネルをブートさせるため、通常はこのアドレスにあるカーネルを呼び出します。
If your mouse isn't working, you will first need to find out if it is detected by the kernel at all.
もしマウスが動作していないのなら、まずカーネルに認識されているかを確認してください。
There are some cool features of the frame buffer devices, in that you can give generic options to the kernel at boot up-time, including options specific to a particular frame buffer device.
起動時にカーネルに一般的なオプションを与えることができ、それには特定のフレームバッファデバイスに固有のオプションも含まれています。