After the bucket cylinder length reaches the set value, open loop control is performed until the target value is reached.
バケットシリンダ長が目標値の手前に設定される設定値に到達するまではフィードバック制御が行われ、バケットシリンダ長が設定値に到達した後は目標値までオープンループ制御が行われる。
An instruction current setting unit includes a target value correction unit which obtains a d-axis and a q-axis current instruction value i dc, i qc to be supplied to an open loop control unit, according to a d-axis and a q-axis current target value id*, iq*.
指令電流設定部は、d軸およびq軸電流目標値id*,iq*に基づき、オープンループ制御部に与えるべきd軸およびq軸電流指令値idc,iqcを求める目標値補正部を備える。
So, it's an open loop control.
In the precoding means, different precoding vectors are applied to different signal sequences and the correspondence between the different precoding vectors and the different signal sequences is decided by an open loop control not depending on a feedback from a reception device.
プリコーディング手段では、互いに異なるプリコーディングベクトルが、異なる信号系列に適用され、異なるプリコーディングベクトル及び異なる信号系列の対応関係は、受信装置からのフィードバックによらない開ループ制御で決定される。
Features 1 Hunting will not occur during automatic operation due to an open loop control.
Test circuit is operated under condition of "Open Loop Control" (GND = 0 V), unless otherwise specified.
特に記述がない限り、測定回路はオープンループ制御 ( GND = 0 V)で動作しています。
Features 1 Open loop control Hunting never occurs due to the use of open loop control.
オープンループ制御: オープンループ制御のため自動運転でもハンチングは発生しません。
The current limit threshold is tightly trimmed allowing open loop control techniques to reduce parts count while maintaining accurate current regulation and high power factor.
この電流制限閾値は厳密に調整されているため、開ループ・コントロール技術で、正確な電流調整と高力率を維持しながら、パーツ数を減らすことができます。
An open loop control unit (22) determines dq axis command voltages vd and vq in accordance with the motor circuit equation based on the command currents id* and iq* and the angular velocity ωe, and sets as the command voltages vd, vq values to which the correction voltages Δvd and Δvq are added.
指令電流算出部21は、操舵トルクTと車速Sに基づき、dq軸上の指令電流id*、iq*を求める。
This time based alarm is selectable and can provide valuable quality control information for a historically open loop control application.
A motor control unit (29) of the inverter device (22) has a parameter map for storing motor parameters, an open loop control unit (37) for using the parameters stored in the parameter map to produce a control amount for a torque command from the ECU (21) through open loop control according to a voltage equation, a current feedback control unit (38) for performing control for eliminating deviation in the command current value produced in the inverter for the torque command from the ECU (21), and a hybrid control unit (39) for controlling the motor (6) according to a control amount produced from the control amount produced by the open loop control unit (37) and the control amount produced by the current feedback control unit (38).
インバータ装置22のモータコントロール部29は、モータパラメータを記憶するパラメータマップと、ECU21からのトルク指令に対して、パラメータマップに記憶されたパラメータを用い、電圧方程式によりオープンループ制御で制御量を生成するオープンループ制御部37と、ECU21からのトルク指令に対してインバータ内部にて生成された指令電流値に対する偏差を無くす制御を行う電流フィードバック制御部38と、オープンループ制御部37で生成された制御量と、電流フィードバック制御部38で生成された制御量とから生成された制御量によりモータ6を制御するハイブリッド制御部39とを有する。
Injection Unit and Control System Both standard open loop control and closed loop control types of molding machines can be used for SUMIKASUPER LCP.
射出ユニットおよびその制御系 スミカスーパー LCPは、一般的なオープンループ制御タイプやクローズドループ制御タイプの成形機が使用可能。
Andere resultaten
When driving a stepping motor by open-loop control, the output current must be set allowing a large safety margin against actual mechanical load torque so as to avoid losing steps.
また、ステッピングモータをオープンループ制御で駆動する場合、脱調を回避するために、実際のメカ負荷トルクに対し大きなマージン(安全率)で出力電流を設定します。