In quad five-level pulser mode, each channel is controlled by three logic inputs and the active return to zero has the same current driving of the pulser 2A (typ).
クワッド5レベルパルサーモードでは、各チャネルが3つのロジック入力によって制御され、アクティブゼロ復帰でパルサーの電流駆動は同じ2A (typ)です。
The number statistics on this subtab return to zero when the capture process is stopped or aborted. These statistics start to accumulate again when the capture process is started.
取得プロセスが停止または中止されると、このサブタブの数値統計はゼロに戻ります。取得プロセスが起動されると、これらの統計は再度蓄積されます。
At this time, press the button again and the LCD screen will return to zero.
この時点で、もう一度ボタンを押すと、LCD画面がゼロに戻ります。
They came from zero and return to zero.
零から出てきたので、零に帰っていきます。
A chronograph timepiece where elapsed time display sections can accurately return to zero and the number of parts is reduced to simplify the structure.
複数の経過時間表示部の正確な帰零を可能にし、部品数を低減して構造を簡素化するクロノグラフ時計を提供する。
When the time is return to zero, the vehicle will automatically enter the flameout state to achieve the cooling state of the turbine.
時間がゼロに戻ると、車両は自動的にフレームアウト状態になり、タービンの冷却状態になります。
If you observe this number get large (in the thousands) or not return to zero within a few seconds, you should investigate the write performance of the repository.
この数が大きくなったり (数千単位)、数秒以内にゼロに戻らなかったりすることが観察される場合、リポジトリの書き込みパフォーマンスを調査する必要があります。
It is sometimes better to return to zero for seeing a whole once the good and bad points are done. It is the view from the reincarnation.
輪廻の思想でいったん良いところも悪いところもゼロ に戻してしまう方が全体で見れば良くなるということもある。
The temperature of the electromagnetic wave absorber will rise against the temperature of the reference block. When this occurs, DC current is reduced to h 2 so that the temperature difference will again return to zero.
この時、電磁波吸収体の温度が温度基準ブロックの温度に比べて高くなるので、温度差が再び0になるまで、直流電力を減少させて h 2 とする。
To return to the hard limits set by the robot manufacturer, press the Reset button. The caution zone will return to zero, and any soft limits previously entered for any of the joints will return to the manufacturer's specifications.
ロボット メーカーにより設定されているハード リミットに戻るには、[リセット] ボタンを押します。警告ゾーンが 0 に戻り、ジョイントに対して以前に入力したソフト リミットがメーカーの仕様に戻ります。
Note: The number statistics on this subtab return to zero when the apply process is stopped or aborted. These statistics start to accumulate again when the apply process is started.
注意: 適用プロセスが停止または強制終了すると、このサブタブの統計値は0に戻ります。適用プロセスが起動すると、この統計値のカウントが再開されます。
Return crown to normal 1 position. NOTE: This procedure should only be performed when chronograph second hand does not to return to zero position.
リューズを通常のポジション1に戻します。 注記:この手順は、クロノグラフの秒針が0の位置に戻っていない場合にのみ実行可能です。
OFF and will not return to zero.
点には戻りません。