Download for Windows Premium
Publiciteit
zero correction value

Vertaling van "zero correction value" in Japans

We konden deze vermelding niet vinden. Er worden benaderende resultaten weergegeven. Controleer je spelling of stel voor deze term aan het woordenboek toe te voegen.
ゼロ補正値
Please check each zero correction value.
それぞれのゼロ補正値を確認してください。
The zero correction value is automatically set and torque display becomes zero.
自動的にゼロ補正値が設定され、トルク表示がゼロになります。
Displays zero correction value which is set in the torque display window for few seconds and return to the torque display.
トルク表示窓に現在設定されているゼロ補正値が数秒間表示され、その後トルク表示に戻ります。
After setting, load the zero correction value to check if the value is changed ±100 or more compare to it at the time of shipment.(It is written in the certification of test result which is attached at the time of shipment.)
その後設定されたゼロ補正値を読みとり、トルク検出器の出荷時のゼロ補正値(出荷時に同梱されている試験成績書に記載)に対し±100 以上大きく違っていないか確認します。
Once you set the torque zero correction value and N-0 correction value, they are stored in backup memory.
トルクのゼロ補正値、N-0補正値は一度設定するとバックアップメモリに記憶されます。
Caution Torque zero correction value and N-0 correction value are changed when the rotation direction of the measurement shaft is changed.
注意 測定する軸の回転方向を変えた場合、トルクのゼロ補正値、N-0補正値が変わります。
Causes of the change of the zero correction value 1.The power of the torque detector is not turned ON.
【ゼロ補正値の変化の要因】 トルク検出器の電源が入っていない。
When the unit is used by switching the rotation direction, it is necessary to set the torque zero correction value and N-0 correction value for each of the CW and CCW directions.
回転方向を切り替えて使用するには、CW/CCW各方向についてトルクのゼロ補正値、N- 0補正値の設定を行う必要があります。
When the setting zero correction value after the zero correction operation is changed ±100 or more compare to it at the time of shipment (It is written in the certification of test result which is attached at the time of shipment.), followings are possible causes.The power of the torque detector is not turned ON, or operated the zero correction in correction is operated while the torque detector is in load state.
ゼロ補正操作を行った後に設定されたゼロ補正値が、トルク検出器の出荷時のゼロ補正値(出荷時に同梱されている試験成績書に記載)に対し±100 以上大きく違っている場合は、 トルク検出器の電源が入っていない、またはその状態でゼロ補正を行った トルク検出器に負荷がかかった状態でゼロ補正を行った 試験する軸の回転方向と CW/CCW の設定が一致していない CW/CCW の設定が検出器側と TS-2700 側で一致していない(TS-2700 の CW/CCW キーは記憶されている CW・CCW のゼロ補正値を切換えています) トルク検出器の故障 の可能性が考えられます。
ONO SOKKI - TorquemeterFAQ -How to check the torque detector is breakdown or not.One procedure to check if the torque detector is breakdown or not is to check "Is the zero correction value changed significantly compare to it at the time of shipment?".
小野測器トルクメータ FAQ -TS-2700 トルクの値がおかしい - トルク検出器が故障かどうか確認する方法 トルク検出器が故障していないか判断する方法としてゼロ補正値が出荷時の値より大きく変化していないかを確認することがあります。
When your personal computer supports the functions of terminal emulator or VT-100 terminal emulator, it is possible to write torque zero correction value and N-0 correction value in TERMINAL mode of TS-2600.Specifications
端末エミュレ-タまたは VT-100 端末エミュレ-タの機能をサポ-トとしているパソコンがある場合は、本器のタ-ミナルモ-ドでトルクのゼロ補正値/N-0 補正値の書き込みができます。仕様
(The CW/CCW key of the TS-2700 is switching the memorized zero correction value of the CW/CCW.)Breakdown of the torque detector If an error does not apply to the above 1 to 5 causes, the detailed confirmation such as linearity is necessary with the detector calibration.
(TS-2700 の CW/CCW キーは記憶されている CW・CCW のゼロ補正値を切換えています) トルク検出器の故障 上記 1 ~ 5 にあてはなまらない場合は検出器の校正を行い直線性など詳細確認が必要です。
Press [LOCK] key again to light up the lamp and press [TRQ ZERO] key for 2 to 3 seconds.This procedure enables to check the zero correction value of the opposite direction in the torque display window.
その後再びLOCKキーを押して点灯させ、TRQ ZEROキーを 2 ~ 3 秒押すと切り換えた方向のゼロ補正値をトルク表示部で確認できます。
Er zijn geen resultaten gevonden voor deze term.
Ga naar Premium voor toegang tot miljoenen vertaalvoorbeelden, onbeperkt woorden opslaan en leren, zonder advertenties.

Synoniemen voor zero correction value in het Engels

Woord & uitdrukking van de dag
Afbeelding van de dag
worm: small animal with a long thin body
Ontdek het woord
Publiciteit

Resultaten: 16. Exact: 16. Verstreken tijd: 21 ms.