Gesproken tekst vertalen, offlinefuncties, synoniemen, vervoegingen, educatieve spelletjes
Publiciteit
Registreer gratis: toegang tot meer resultaten en functies
minimum yield strength
Examples with "minimum yield strength" and their translation in Chinees
For casing joint bolting, the allowable stress, as determined in 6.3.1.2 shall be used to determine the total bolting area based on hydrostatic load and gasket preload, as applicable. The preload stress shall not exceed 0.75 times the bolting material minimum yield strength.
对于连接泵体的螺栓的许用应力，应按照6.3.1.2的要求基于泵体螺栓连接处承受的液压作用力和密封垫所需的预 紧力进行计算校核。螺栓预紧力不应超过超过螺栓材料最低屈服强度的0.75倍。
7.4.10.1 The lifting lugs and attachment methods shall be designed using a maximum allowable stress of one -third of the specified minimum yield strength of the lifting lug welds shall be inspected by either liquid penetrant or magnetic particle testing.
吊耳及其连接方式设计的最大许用应力应不大于对应材料最小屈服强度的1/3.每一个吊耳焊接都应采用磁粉探伤或 者液体渗透检查。
All concrete reinforcement bars shall be coated/ uncoated as per table 1 of SAES-Q-001, based on the exposure type defined in the Geotechnical report, high tensile deformed steel bars with minimum yield strength of 60 KSI as per SAUDI ARAMCO Engineering Standard SAES-Q-001 & 09- SAMSS-106.
所有混凝土钢筋和最小屈服强度为60 KSI的高强度螺纹钢筋应分别根据SAES-Q-001表1和沙特阿美石油公司工程标准SAES-Q-001和09- SAMSS-106，基于岩土工程勘察报告中定义的裸露类型，选择涂敷/不涂覆涂料。
The allowable tensile stress used in the design of the pressure components, excluding bolting, for any material shall not exceed 0.25 times the minimum ultimate tensile strength or 0.67 times the minimum yield strength for the material whichever is lower across the full range of specified operating temperature.
承受因压力导致的拉伸应力的零部件（螺栓除外）设计，无论使用任何材料，在规定的全部操作温度范围内零件受 到的拉伸应力不得超过0.25倍材料最低极限拉伸应力或0.67倍材料最低屈服应力（取二者之中的最低值）。
Andere resultaten
ArcelorMittal 12: for drawing, with minimum guaranteed yield strength
安赛乐米塔尔 12： 最下屈服强度值的冲压
When the bar shall be substituted, the ratio of tensile strength versus yield strength, strength, minimum reinforcement rate, structural deformation and crack control shall all meet the specification requirement, and shall be confirmed by the design unit.
钢筋需代换时，必须注意强屈比、强度、最小配筋率、构造变形及裂缝控制均应满足规范要求，并经设计单位确认。
When the elongation exceeds the minimum value, for each increase of 1%, the tensile strength and yield strength may be reduced by 10MPa, however, the minimum value of the tensile strength shall not be lower than 400MPa.
当伸长率超过最低值时，每增加1%，拉抗强度和屈服强度可减少10MPa，但抗拉强度最低值不得小于400MPa。
Welding consumables, in addition, shall be such that they produce weld metal which, when tested in accordance with the applicable method given in BS 709, has a minimum yield stress and minimum tensile strength at least equal to those of the parent metal.
焊接消耗品焊接的金属在根据《英国标准》第709条中的可适用方法测试时，最低屈服应力和最小拉力强度至少等于底层金属的屈服应力和拉力强度。
Desirable properties for forming include low yield strength and high ductility.
令人满意的成形特性包含了低降伏应力和高延展性。
At least a minimum yield is guaranteed even under difficult conditions.
即使在恶劣条件下起码的最低产量得到保障。
Expandable library of material properties, yield strengths, and limit stresses
可扩展的数据库，包括材料属性、屈服强度以及极限应力
The allowable stress is given by the yield strength of the shaft material.
容许应力由轴材料的屈服强度给出。
The specified minimum yield is greater than the target yield.
目标收率比指定的下限收率低。
Ga naar Premium voor toegang tot miljoenen vertaalvoorbeelden, onbeperkt woorden opslaan en leren, zonder advertenties.
Synoniemen voor minimum yield strength in het Engels
Woord & uitdrukking van de dag
Afbeelding van de dag
Resultaten: 122. Exact: 4. Verstreken tijd: 71 ms.
