Subtract 4 bytes for each tag popped in the rewrite command configured under the sub-interface.
Soustrayez 4 octets pour chaque balise sautée dans la commande de réécriture configurée sous la sous-interface.
As a workaround, sub-interface configuration (provided that the device connected to the router supports dot1q tagging) to separate the two subnets can be configured, so both of them get their correspondent IP addresses properly.
Pour contourner le problème, une sous-interface (à condition que le périphérique connecté au routeur prenne en charge l'étiquetage dot1q) peut être configurée pour séparer les deux sous-réseaux, de sorte qu'ils obtiennent leurs adresses IP respectives correctement.
As a result, L3 packets of the same size can be forwarded both on the main interface and the sub-interface.
En conséquence, les paquets L3 de la même taille peuvent être expédiés sur l'interface principale et la sous-interface.
Because there is one tag configured on the sub-interface with the dot1q vlan 201 command, add 4 bytes to 1514 for an MTU of 1518 bytes.
Puisqu'il y a une balise configurée sur la sous-interface avec la commande du dot1q vlan 201, ajoutez 4 octets à 1514 pour un MTU de 1518 octets.
transmitting the TRUNK sub-interface information mapped to the primary physical unit port to the secondary physical unit port
transmettre les informations de sous-interface JONCTION mappées sur le port d'unité physique primaire au port d'unité physique secondaire
This behavior change can cause problems in the case of a sub-interface configured with a single VLAN tag, but receives packets with two VLAN tags.
Cette modification de comportement peut poser des problèmes dans le cas d'une sous-interface configurée avec une balise de VLAN simple, mais reçoit des paquets avec deux balises VLAN.
In order to eliminate that condition, the interface MTU can either be increased by 4 bytes or the sub-interface configured with two VLAN tags.
Afin d'éliminer cette condition, l'interface MTU peut être augmentée par 4 octets ou la sous-interface configurée avec deux balises VLAN.
When you are computing the payload size for MPLS LDP to signal, subtract the size of the tags from the MTU of the sub-interface, as seen in the show interface command.
Quand vous calculez la taille de charge utile pour MPLS LDP pour signaler, soustrayez la taille des balises du MTU de la sous-interface, comme vu dans la commande d'interface d'exposition.
In the Cisco IOS software versions earlier than 12.1(3)T, you cannot define the native VLAN explicitly, as the encapsulation dot1Q 1 native command under the sub-interface is not available.
Dans les versions du logiciel Cisco IOS antérieures à 12.1(3)T, vous ne pouvez pas définir le VLAN natif explicitement, car la commande d'encapsulation dot1Q 1 native dans la sous-interface n'est pas disponible.
In addition, if the primary connection is via Frame Relay, the Frame Relay configuration must be done on a point-to-point Serial sub-interface, and the telephone company must be passing the "Active" bit.
En outre, si la connexion principale est par l'intermédiaire de Relais de trames, la configuration de Relais de trames doit être faite sur une sous-interface séquentielle point par point, et l'opérateur téléphonique doit passer le bit « actif ».
Based on this sub-interface MTU, compute the MTU of the MPLS LDP payload that is signaled to the neighbor, and make sure that it is identical to the one computed by the remote L2VPN PE.
Basé sur ce MTU de sous-interface, calculez le MTU de la charge utile MPLS LDP qui est signalée au voisin, et assurez-vous qu'elle est identique à celui calculé par le PE de L2VPN distant.
Although a parent relationship exists conceptually between these interfaces, GeoAPI does not define TransfiniteSet as a sub-interface of java.util.Set, as the definition of certain methods such as size() and iterator() would be problematic.
Bien qu'un lien de parenté existe conceptuellement entre ces interfaces, GeoAPI ne définit pas TransfiniteSet comme une sous-interface de java.util.Set car la définition de certaines méthodes telles que size() et iterator() serait problématique.
In the earlier Cisco IOS versions, it is important to configure the native VLAN-Interface not as a sub-interface, which is in our example VLAN1.
Dans les versions antérieures du logiciel Cisco IOS, il est important de ne pas configurer l'interface VLAN native comme une sous-interface, comme le montre notre exemple VLAN1.