For instance, if the datum is (0,0,0) and the tool axis is Z, then the reference point is (0,0,0) and only holes that lie between the specified minimum and maximum Z values (heights) are detected.
예를 들어, 데이텀이 (0,0,0)이고 공구 축이 Z인 경우 참조 점이 (0,0,0)이면 지정한 최소 및 최대 Z 값(높이) 사이에 배치된 구멍만 검색됩니다.
If a spiral that meets the specified minimum R/A ratio does not fit between a curve and a tangent, then the tangent (4) is moved toward the curve until a solution is found.
지정한 최소 R/A 비율을 충족하는 완화곡선이 원곡선과 접선 사이에 맞지 않는 경우 접선(4)은 솔루션이 발견될 때가지 원곡선 쪽으로 이동합니다.
You can specify that a password must be at least the specified minimum length.
비밀번호가 지정된 최소 길이 이상이어야 한다는 것을 지정할 수 있습니다.
In this exercise, you will draw a profile that refers to specified minimum standards.
이 연습에서는 지정된 최소 표준을 참조하는 종단을 그립니다.
Depending on the hose configuration, the specified minimum bend radius value can be violated during routing.
호스 구성에 따라 경로설정 도중에 지정된 최소 벤드 반지름 값이 위반될 수 있습니다.
If automatically inserting cross sections, you can specify a prompt for segments below a specified minimum length.
횡단을 자동으로 삽입하는 경우 지정된 최소 길이보다 작은 세그먼트에 대해 프롬프트를 지정할 수 있습니다.
The position of segments and routed and unrouted wires in a harness assembly can sometimes violate the specified minimum bend radius.
하네스 조립품에 있는 세그먼트와 라우팅 및 언라우팅된 와이어의 위치는 지정된 최소 절곡부 반지름 을 경우에 따라 위반할 수 있습니다.
There is always a specified minimum drop distance between the lowest incoming pipe and the highest outgoing pipe.
들어오는 가장 낮은 파이프와 나가는 가장 높은 파이프 사이에는 항상 지정된 최소 단차 거리가 있습니다.
If the converted value has fewer characters than the specified minimum field width, trailing or leading spaces are added to the field.
변환된 값의 문자 수가 지정된 최소 필드 너비보다 적으면 필드 앞이나 뒤에 공백이 추가됩니다.
For example, you can create a design check to issue a notification if a tangent is shorter than a specified minimum tangent length.
예를 들어 접선이 지정된 최소 접선 길이보다 짧은 경우 알림을 표시하는 설계 검사를 작성할 수 있습니다.
Checks for bends that do not meet the specified minimum bend radius on segments, and routed and unrouted wires and cables in the active harness assembly.
활성 하네스 조립품에 있는 세그먼트와 라우팅 및 언라우팅된 와이어 및 케이블에서 지정된 최소 절곡부 반지름을 위반하는 절곡부가 있는지 검사합니다.
Contenu potentiellement sensible ou inapproprié
Les exemples vous aident à traduire le mot ou l’expression cherchés dans des contextes variés. Ils ne sont ni sélectionnés ni validés par nous et peuvent contenir des mots ou des idées inappropriés. Signalez des exemples à modifier ou à retirer. Les traductions potentiellement sensibles, inappropriées ou familières sont généralement marquées de rouge ou d’orange.