The drive device includes a rectangular wave voltage source and a control unit.
A drive circuit includes a discontinuous rectangular wave oscillator and a low pass filter.
駆動回路は、不連続矩形波発振器及びローパスフィルタから構成されている。
Provided is a motor drive control device which enables an improvement in fuel efficiency in using electric power while preventing the battery voltage from falling below a lower limit because of rectangular wave control.
矩形波制御を行うことによるバッテリ電圧下限割れを防止しつつ電力的な燃費向上を可能にするモータ駆動制御装置を提供する。
On the other hand, the ions captured already are diffused easily but since the frequency of the rectangular wave voltage decreases before the ions deviate from a stable track, scattering of ions can be avoided.
一方、既に捕捉されていたイオンは発散し易くなるが、安定軌道を外れる前に矩形波電圧の周波数が下がるので、イオンの散逸も回避できる。
When the motor operating point is included in the resonance area without voltage boosting by the converter circuit, the motor control device allows rectangular wave control of the motor limited to a specific time.
そのモータ制御装置は、コンバータ回路が昇圧を行っておらず、モータの動作点が共振域に含まれる場合に、所定時間に限りモータの矩形波制御を許容する。
Immunity is the applied voltage at which an erroneous operation monitor function of the electronic circuit firstly detects an erroneous operation while gradually increasing the wave height value of the rectangular wave.
電子回路の誤動作監視機能が矩形波の波高値を徐々に高めて初めて誤動作する印加電圧をイミュニティとする。
The source generates a rectangular wave voltage according to a first control, and applies the voltage to at least one organic electroluminescent element, thereby driving the element.
該源は、第1制御に従って、矩形波電圧を発生し、少なくとも1つの有機エレクトロルミネッセンス素子に該電圧を印加して該素子を駆動する。
At the secondary terminal of the capacitor (10), the same voltage as that of the rectangular wave appears as the input voltage of the secondary side.
コンデンサ10の2次端子には矩形波と同じ電圧が2次側の入力電圧として現れる。
In case of positive ions, for example, irradiation timing of laser light is adjusted such that the target ions reach the ion inlet (25) during the low level interval in one period of the rectangular wave voltage.
例えば正イオンの場合、矩形波電圧の1周期中のローレベル期間中に目的イオンがイオン導入口(25)に到達するようにレーザ光照射のタイミングを調整する。
The first map is a map which includes a relatively wide rectangular wave control region (a3) because the pressure rising start point of the converter (12) is set within a higher rotation range than in the second map, and the second map is a map for mainly performing pulse width modulation control.
第1のマップは第2のマップよりもコンバータ12の昇圧開始ポイントが高回転域に設定されることで比較的広い矩形波制御領域a3を含むマップであり、第2のマップは主としてパルス幅変調制御を実行するためのマップである。
While applying a rectangular wave voltage to a ring electrode (21) such that ions captured already by an ion trap (20) are not diffused, irradiation timing of laser light for ion generation is controlled such that the ions reach an ion inlet (25) at a predetermined timing in one period of that voltage.
既にイオントラップ(20)に捕捉されているイオンが発散しないように、リング電極(21)に矩形波電圧を印加しながら、その電圧の1周期中の所定のタイミングでイオンがイオン導入口(25)に到達するように、イオン生成のためのレーザ光の照射タイミングを制御する。
The voltage difference computing section (320) computes the difference between the voltage determined by a first voltage command in executing rectangular wave voltage control and the voltage determined by a second voltage command in executing pulse width modulation control.
電圧偏差演算部(320)は、交流電動機の電圧方程式に電流偏差を代入することにより、矩形波電圧制御の実行時における第1の電圧指令と、パルス幅変調制御の実行時における第2の電圧指令との電圧偏差を演算する。
The control device (30) is configured so as to select a first operation mode which instructs a first boost target value to a predetermined same input signal indicating a torque request and specifies a non-rectangular wave control as the control method and a second operation mode which instructs a second boost target value lower than the first boost target value to the predetermined same input signal and specifies a rectangular wave control as the control method.
制御装置(30)は、トルクの要求を示す同じ所定の入力信号に対して、第1の昇圧目標値を指示し制御方式として非矩形波制御を指定する第1の動作モードと、第1の昇圧目標値より低い第2の昇圧目標値を指示し制御方式として矩形波制御を指定する第2の動作モードとを選択可能に構成される。